When it comes to deep cleaning carpets and upholstery, the Bissell extractor is a popular choice for households and businesses alike. The extractor uses a combination of suction, heat, and cleaning solution to remove dirt and grime from various surfaces. However, many people are unsure about how to use a Bissell extractor effectively. In this article, we will provide step-by-step instructions on how to use a Bissell extractor to properly clean your carpets and upholstery.
Step 1: Gather the Necessary Supplies
Before you can start using your Bissell extractor, you will need to gather all of the necessary supplies. These supplies include:
- Bissell extractor
- Cleaning solution
- Water
- Clean towels
- Vacuum cleaner
Step 2: Vacuum the Area
Before you start using the Bissell extractor, you need to vacuum the area that you want to clean thoroughly. This step removes any loose dirt, dust, or debris that could clog the extractor or interfere with the cleaning process. Use a vacuum cleaner with a beater brush to help loosen and remove embedded dirt and pet hair.
Step 3: Prepare the Bissell Extractor
Next, you need to prepare the Bissell extractor for use. Begin by filling the clean water tank with hot water and the recommended amount of cleaning solution according to the manufacturer’s instructions. Then, replace the tank on the extractor and plug it in. Allow the extractor to heat up for a few minutes so the water and cleaning solution can reach the desired temperature.
Step 4: Test the Bissell Extractor
Before using the extractor on your carpets or upholstery, you should test it on a hidden or inconspicuous area, such as a corner or behind a sofa, to make sure it doesn’t cause any damage. Turn the extractor on and use the trigger to spray a small amount of water and cleaning solution on the test area. Then, press the extractor’s trigger and move the machine over the area. Check to make sure the area is not damaged after cleaning.
Step 5: Start Cleaning with Your Bissell Extractor
Once you have tested the Bissell extractor, you can start using it to clean your carpets and upholstery. Turn on the machine and depress the trigger to spray a moderate amount of cleaning solution into the carpet or upholstery. Then, release the trigger and move the extractor forward in a straight line. Pull the machine back over the same area to suction up any dirt and grime. Continue moving the extractor back and forth in a straight line, overlapping each previous pass by one inch until you have cleaned the entire area.
Step 6: Rinse the Carpet or Upholstery
After you have used the Bissell extractor to clean your carpets or upholstery, you need to rinse the area thoroughly to remove any remaining cleaning solution. To rinse the area, fill the clean water tank with hot water only and run the extractor over the area again. Continue to rinse the area until the water that is suctioned back out of the carpet or upholstery is clear.
Step 7: Dry the Area
Finally, you need to dry the carpet or upholstery after cleaning it with the Bissell extractor. Use clean towels to soak up as much moisture as possible. If possible, use a fan or open windows to promote air circulation and speed up the drying process.
Using a Bissell extractor is an effective way to deep clean your carpets and upholstery. By following these steps, you can get your carpets and upholstery looking and smelling fresh and clean in no time.
Recommended for you: Is It Better To Sweep Or Vacuum Hardwood Floors?
Frequently Asked Questions – How Do You Use A Bissell Extractor?
1. How do I fill the water tank of a Bissell extractor?
First, ensure that the machine is unplugged from the power source. Next, lift the clean water tank off the unit and remove the lid. Fill the tank with hot water up to the marked fill line. Add cleaning solution according to the manufacturer’s instructions, and then replace the tank lid and secure it in place.
2. How do I use the Bissell extractor on my carpet?
Before using the extractor, vacuum the carpet thoroughly to remove any loose debris. Attach the appropriate cleaning tool to the end of the hose and turn the machine on. Press the trigger to release the cleaning solution and move the machine forward over the carpet. Release the trigger and lean back to make a second pass over the same area with the suction on to remove as much water as possible. Repeat this process until you have cleaned the entire carpet.
3. How do I clean and maintain my Bissell extractor?
After each use, empty the dirty water tank and rinse it thoroughly. Clean the brushes and nozzle with a damp cloth or brush to remove dirt and debris. Periodically, detach the hose and clean it and the accessory tools to prevent blockages. Refer to your user manual for specific maintenance instructions.
4. Can I use the Bissell extractor on upholstery?
Yes, Bissell extractors come with a variety of attachments that can be used to clean upholstery, stairs, and other smaller areas. However, be sure to check the manufacturer’s instructions for specific guidance on using the machine on different surfaces.
You might be interested in: Unlocking the Mystery: What Year Was the Roomba 655 Released?